|
|
Acrylonitrile
Styrene Acrylate (ASA)
| ASA
PROPERTIES |
 |
Typical
Properties |
Test
Method |
Units |
ASA
306 UV |
ASA
302 UV |
|
IZOD
Impact |
|
|
|
|
(12.7
x 3.2mm, notched) |
ASTM D256 |
J/m |
300 |
275 |
|
Tensile
Strength at 5 mm/min |
|
|
|
|
(12.7
x 3.2mm) |
ASTM D638 |
MPa |
40 |
47 |
|
Tensile
Modulus at 5 mm/min |
|
|
|
|
|
(12.7
x 3.2mm) |
ASTM D638 |
MPa |
2000 |
|
|
Flexural
Strength at 1.3mm/min |
|
|
|
|
|
(12.7
x 3.2mm) |
ASTM D790 |
MPa |
65 |
76 |
|
Flexural
Modulus at 1.3mm/min |
|
|
|
|
|
(12.7
x 3.2mm) |
ASTM D790 |
MPa |
2100 |
2450 |
|
Heat
Deflection Temp. |
|
|
|
|
|
(12.7
x 12.7 x 127mm, 1.82 MPa) |
ASTM D648 |
C (unannealed, |
88 |
89 |
|
|
|
compression moulded) |
|
|
|
Coefficient
of Linear Thermal Expansion |
ASTM D696 |
Cm/cm/ C |
9.5 x 10-5 |
9.5 x 10-5 |
|
Vicat
Softening Point (1 kg) |
ASTM D1525 |
C |
105 |
104 |
|
Glow
Wire Test Pass Temperature (1.57mm) |
AS 2420 |
C |
550 |
550 |
|
Specific
Gravity |
ASTM D792 |
- |
1.05 |
1.06 |
|
Rockwell
Hardness |
ASTM D785 |
R |
90 |
100 |
|
Mould
Shrinkage |
ASTM D955 |
% |
0.5 0.2 |
0.6 0.2 |
|
ASA
PROPERTIES |
|
|
|
|
|
Typical
Properties |
Test
Method |
Units |
797
SE UV |
776
SE UV |
|
IZOD
Impact |
|
|
|
|
|
(12.7
x 3.2mm, notched) |
ISO 180/1A |
KJ/m2 |
30 |
15 |
|
Tensile
Strength at 5 mm/min |
|
|
|
|
|
(12.7
x 3.2mm) |
ISO 527-2 |
MPa |
42 |
47 |
|
Tensile
Modulus at 5 mm/min |
|
|
|
|
|
(12.7
x 3.2mm) |
ISO 527-2 |
MPa |
2000 |
2200 |
|
Flexural
Strength at 1.3mm/min |
|
|
|
|
|
(12.7
x 3.2mm) |
ISO 178 |
MPa |
60 |
65 |
|
Flexural
Modulus at 1.3mm/min |
|
|
|
|
|
(12.7
x 3.2mm) |
ISO 6721-2 |
MPa |
730 |
800 |
|
Heat
Deflection Temp. |
|
|
|
|
|
(12.7
x 12.7 x 127mm, 1.82 MPa) |
ISO 75-2 |
C |
95 |
96 |
|
Coefficient
of Linear Thermal Expansion |
|
|
|
|
|
Longitud.
(23-80) C |
DIN 53752 |
10-5K |
8-11 |
37203 |
|
Vicat
Softening Point (1 kg) |
ISO 306 |
C |
104 |
104 |
|
Specific
Gravity |
ASTM D792 |
- |
1.1 |
1.1 |
|
TOLERANCES (All dimensions are
measured at 22-24 degrees Celsius).
|
| |
Length |
width |
thickness |
Sheet
length up to 1.5m |
+3/-1.5mm |
+1.5/-1.5mm |
5% |
Sheet
length 1.5m to 4m |
+10/-0mm |
+5/-0mm |
5% |
Special
sizes over 4m |
+20/-0mm |
+5/-0mm |
5% |
|
|
